- 1 What is the thumb method of casting on stitches?
- 2 What is the advantage of casting on thumb method?
- 3 What is the easiest way to cast on in knitting?
- 4 How much yarn does it take to cast a thumb?
- 5 What is long tail cast on method in knitting?
- 6 What is the best cast on for ribbing?
- 7 What is the best cast on for a blanket?
- 8 Why is my cast on row so loose?
- 9 Do you cast on the first row of knitting?
- 10 How do I calculate yarn for cast on?
- 11 How do you measure yarn for long-tail cast on?
- 12 How do I know how many stitches to cast on?
What is the thumb method of casting on stitches?
1Make a slip knot on your needle, leaving a short tail. 2Wrap the yarn around your left thumb. 3Insert the needle through the loop around your thumb, slide your thumb out, and pull gently on the yarn strand to tighten the stitch.
What is the advantage of casting on thumb method?
The advantages of the thumb cast on: It creates a stretchy cast on and therefore is suitable for garments that need give e.g. sock and mitt cuffs (a revelation for me as hinted at in the introduction above!) It is simple to do in the middle of your knitting as you continue to work in the same direction.
What is the easiest way to cast on in knitting?
Knitted Cast On
- Make a slip knot and put it on your needle.
- Pass the needle in the right hand through the loop on the left needle and bring the right needle under the left needle.
- With your left hand, wrap the working yarn around your left hand needle.
- Bring the right needle back through the loop on the left needle.
How much yarn does it take to cast a thumb?
#1 The Rule of thumb method If you got a short work, with only a couple of stitches to knit, then a simple rule of thumb will help you out. Simply set aside 4 times as much yarn as your final work will be wide. So, if you want to knit a scarf that is 10 inches wide, set aside 40 inches.
What is long tail cast on method in knitting?
Unlike the knit cast -on or cable cast -on, this one does not begin near the beginning of the ball of yarn. Instead, you have to start with a long tail, and the stitches are formed using both the tail and the yarn attached to the ball. The trick is to make sure that the tail is long enough for your project.
What is the best cast on for ribbing?
Best Cast Ons for Ribbing: Alternating Cable Cast On for 1×1 Rib
- Leaving a tail for weaving in, tie a slip knot on needle.
- Insert RH needle into first stitch on LH from front to back; yarn-over knitwise and pull through a loop; place loop on LH needle.
What is the best cast on for a blanket?
Cable cast -on, imo, as long as you can keep your tension uniform. I love how neat it looks. I love the crochet cast on because you don’t have to pre-measure your yarn for the cast on. Lots of knitters use this method for provisional cast ons.
Why is my cast on row so loose?
If your cast -on stitches are too loose, you can try using needles a size or two smaller. But make sure you don’t overcompensate and make your stitches too tight. You can also try to space the stitches closer together on the needle as you cast on. Most cast ons start with a slipknot (right).
Do you cast on the first row of knitting?
The cast on itself is not counted, however, some cast on methods create both a cast on and a knitted row. For example, the most popular cast on, the long tail method, creates both a cast on and a knitted row. So in this case, you would count that as the first row.
How do I calculate yarn for cast on?
- Cast on 10 stitches using long-tail cast on method.
- With one hand, hold end of tail close to last stitch cast on.
- Measure the length of yarn between your hands.
- Divide number of stitches you want to cast on by 10, multiply the result by measurement from step #3, and round up to nearest whole number.
How do you measure yarn for long-tail cast on?
If you need 20 stitches of 4mm diameter stitches, then you’ll need a minimum of 20 x 1.26cm length. Convert to inches (1” per 2.54cm) and you’ve got roughly 10” minimum for the tail to cast on. Add a few more inches so that you’ll have yarn to hold on to at the end; four to five inches should do it. Try it yourself!
How do I know how many stitches to cast on?
The Stitches to Cast-On = (dW x S/W). Divide Stitches counted in swatch by swatch Width measured. Multiply by Desired Width. So for the example for the above you will take your 4×4 measured area.